STEREO POWERED MIXEROWNER’S MANUALPSX1000PSX1600PSX2200
FX1/FX2The PSX offers two independent, identically-configured 18-bit stereo effect units – FX1 and FX2. Each unitprovides 99 program presets which are
30. FX ONThese switches are used to turn the internal FX units on – the green LED is lit. Please keep in mind thatyou also can use an external foot s
Typically, the AUX3 channel is used as monitor bus. Depending on the setting of the AUX3 POST switch, it is alsopossible to configure the bus for the
49. MAIN INSERTSStereo phone jacks for the left and the right channels with breaker function. The low impedance outputis assigned to the tip (send) an
55. POWER AMP STATUS indicatorsThese indicators inform you about the momentary operational status of the PSX’s internalpower amplifier.The POWER ON in
The frequency ranges and the characteristics of the of the equalizer were carefully chosenfor live sound. If you want a clear and intelligible sound,
CABLINGThe ac power cord comes with the PSX. The quality of all other cables are your responsibility. Carefully chosen high quality cables are thebest
CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Input/Mono . . . .
In this chapter we would like to explain how to install a typical sound reinforcement system in passive configuration and incorporating stagemonitor s
• Pull all faders down and engage the PSX’s STANDBY button to prevent unwanted feedback. •First, switch the PSX on and then the external amplifier. •
MAIN MIX• Position the master faders in the range between –30dB and –20dB.•Establish a basic mix, using the channel faders, so that the individual sou
All inputs and outputs in the master section are referred to as the MASTER PATCHBAY.The mixer’s LINE OUTPUTS, RETURNS, and INSERTS are found here. To
3. Using the internal power amplifier for monitoring or side-fill purposes:In case you want to use an external power amplifier to drive your main spea
5. Maximum amount of speakers in a passive configuration:The PSX allows connection of up to three loudspeaker cabinets with an impedance of 8 ohms per
Technical Specifications PSX Mixing desk in rated condition, Unity Gain ( MIC Gain 20 dB ), all faders position 0 dB, all pots in mid position, Master
BLOCK DIAGRAM27 of 32
Dimensions in mm (inch)DIMENSIONS28 of 32
WARRANTY (Limited)Electro-Voice products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as note
FIRST OF ALL, WE WOULD LIKE TO THANK YOU AND CONGRATULATE YOU TO YOUR PURCHASE OF A ELECTRO-VOICEPOWER MIXER.The design of the PSX compact power mixer
1. MICElectronically balanced XLR-type inputs for the connection of low impedance microphones, like the ones that arefeatured in big studio -and live
If you want to use this socket as a DIRECT OUT (Pre EQ), the stereo phone plug’s tip and ring have to be shortcircuited, so that the audio signal is n
7. EQ SECTIONThe mixer’s EQ section allows shaping of the audio signal within different frequency bands. Turning one of theEQ level controls to the r
9. AUX 3The AUX 3 control is primarily meant for the monitor mix. Nevertheless, when the master section’s AUX3 POSTbutton is pressed, it can also be u
Since most features of the stereo inputs are virtually identical to those of the monaural inputs, we will not discusstheir functions in detail again.
18. EQ SECTIONThe mixer’s EQ section allows very differentiated shaping of the incoming audio signal within miscellaneousfrequency bands. Turning one
Comments to this Manuals